Alabama GC License #60291 · Duro-Last Approved Contractor · Licensed · Bonded · Insured · Since 2022

Commercial Roofing in Mobile and Baldwin County, AL

Wise Builders installs, repairs, and maintains commercial roofs across Mobile and Baldwin County: PVC, TPO, metal, coatings, and flat roofs on offices, retail centers, metal buildings, churches, and apartments.

We are a licensed general contractor and a Duro-Last approved contractor. You get one project manager, one written scope, one fixed price, and No-Dollar-Limit manufacturer warranties up to 30 years.

Call (251) 305-7282 for a free roof inspection.

★★★★★ 5.0 on Google · 160+ verified reviews · Alabama GC License #60291 · Licensed, bonded & insured

Schedule a free analysis today

5.0Google rating
160+Verified reviews
100%Satisfaction guarantee
2022Serving the Gulf Coast since
Alabama GC License #60291Duro-Last approved contractorNDL warranties up to 30 years5-year workmanship warrantyMobile and Baldwin County
What We Do

Commercial Roofing Systems We Install and Service

Most low-slope roofs in Mobile and Baldwin County are single-ply, metal, or an older built-up or mod-bit roof. We install, repair, restore, and maintain all of them. Building in Foley, Gulf Shores, or Orange Beach? See commercial roofing in Foley and Baldwin County.

01

PVC Roofing

Duro-Last PVC, factory-made flashings, and No-Dollar-Limit warranties up to 30 years.

See PVC roofing
02

TPO Roofing

60 and 80 mil TPO, mechanically attached or fully adhered, over insulation sized for your building.

See TPO roofing
03

Commercial Metal Roofs

Retrofits over rusted metal, new R-panel and standing seam, and metal roof coatings.

See commercial metal roofs
04

Roof Coatings

Silicone and acrylic restoration for metal, single-ply, and mod-bit roofs that are still dry underneath.

See roof coatings
05

Flat Roofs

Ponding, leaks, and worn-out flat roofs: repair, coat, recover, or replace.

See flat roofs
06

Spray Foam Roof Restoration

Silicone recoats and repairs for existing foam roofs, and replacement when the foam is done.

See spray foam roof restoration

Replacement, Repair and Maintenance

Every system above gets the same three services.

01

Roof Replacement

Tear-off, recover, or retrofit, with core cuts before we price and a fixed number in writing.

See roof replacement
02

Roof Repair

Leak tracing and repair on TPO, PVC, metal, mod-bit, and built-up roofs. 24/7 emergency calls.

See roof repair
03

Maintenance Plans

Scheduled inspections, drains cleared, small repairs, and a photo report after every visit.

See maintenance plans

Buildings We Roof

Small and mid-size commercial buildings across Mobile and Baldwin County.

  • Offices, retail centers, and strip centers.
  • Metal shops, warehouses, and pre-engineered metal buildings.
  • Churches: sanctuaries, fellowship halls, and education wings.
  • Apartments, condos, and HOAs.
  • Restaurants, clinics, schools, and nonprofit buildings.

What Every Proposal Includes

No vague square-foot quote. You see what you are buying.

  • Core cut results and moisture readings from your roof.
  • Every layer: insulation, cover board, membrane or panel, and thickness.
  • Fastening pattern and edge metal sized to your address.
  • Unit prices for hidden deck, purlin, or wet-insulation repair.
  • The warranty term, in writing, with a sample warranty attached.
Investment

What a Commercial Roof Costs on the Gulf Coast

A commercial roof price depends on what is under the membrane more than the membrane itself. Here is what each option typically costs, and what moves the number.

Typical Gulf Coast Cost Ranges

Typical Gulf Coast ranges for a 10,000 square foot low-slope roof. Your inspection replaces these with one fixed price.

SystemCost per Sq Ft10,000 Sq Ft RoofOn-Site Time
Silicone coating restorationponding areas, single-ply or mod-bit$3.50 to $6.00$35,000 to $60,0004 to 7 working days
Single-ply recover over a dry existing roofTPO or PVC with cover board$8.00 to $11.00$80,000 to $110,0001 to 2 weeks
PVC or TPO retrofit over a metal roofflute fill, insulation board, new membrane, edge metal$6.00 to $8.00$60,000 to $80,0002 to 3 weeks
TPO tear-off and replace60 mil, code insulation, new edge metal$13.00 to $16.00$130,000 to $160,0002 to 3 weeks
PVC tear-off and replace50 to 60 mil, code insulation, new edge metal$13.00 to $16.00$130,000 to $160,0002 to 3 weeks
R-panel metal roof replacementpainted steel, with insulation$11.00 to $13.00$110,000 to $130,0002 to 3 weeks
Standing seam steel roofPVDF finish$15.00 to $22.00$150,000 to $220,0003 to 4 weeks

The cheapest roof is the one you do not have to tear off. If core cuts show the existing roof and insulation are dry, a coating or a recover costs well under a tear-off: $3.50 to $6.00 per square foot for a coating or $8.00 to $11.00 for a recover, against $13.00 to $16.00 for a full tear-off with new insulation. If the insulation is wet, it has to come out.

What Moves a Commercial Roof Price

Two roofs the same size can be priced tens of thousands of dollars apart. These are the reasons, and we put each one in writing.

01

Tear-Off and Wet Insulation

A full tear-off with new insulation runs $13.00 to $16.00 per square foot, against $8.00 to $11.00 for a recover. Older Mobile buildings often have two layers, and wet insulation found in core cuts has to be replaced. We cut cores before we price.

02

Wind Design at the Edges

The corners and perimeter of a roof take the most wind. They get more fasteners or adhesive and heavier edge metal, sized to the design wind speed for your address.

03

Penetrations, Curbs and Gutters

Every HVAC curb, skylight, vent, and drain is a detail that has to be flashed. Gutters, downspouts, and new edge metal are often half the line items on a metal building.

Ranges are installed costs for a simple 10,000 square foot low-slope roof. Deck, purlin, and wet-insulation replacement, HVAC curb work, and permits are priced after we inspect the roof.

★★★★★Google Review

"Jim Brock is the best project manager ever! He constantly communicated with me about the materials, build and timeline. No stones were unturned! Exceptional work by his team."

Marcus Mitchell, Google review, November 2023

How It Works

From Inspection to Warranty

Every commercial roof runs through one contract and one project manager. You make the decisions. We carry the crew, the permit, the inspections, and the warranty paperwork.

01

Step 1. Roof Inspection and Core Cuts

We walk the roof and check the membrane or panels, seams, flashings, curbs, drains, gutters, and edge metal. We cut cores to see the layers and test the insulation for moisture, and we look at the deck or purlins from inside when we can.

02

Step 2. Options and a Fixed Price

You get a written proposal with every layer, thickness, fastening pattern, and warranty term listed, plus a fixed price. When repair, coating, recover, and replacement are all real options, we price them side by side.

03

Step 3. Wind Design and Permit

We size the fastening, perimeter and corner enhancement, and edge metal to the design wind speed for your address, then pull the permit with the city or county that has your building.

04

Step 4. Schedule Around Your Business

We plan the work around your hours. On occupied buildings we work in sections, protect HVAC intakes, and dry in every section before the crew leaves. Your doors stay open.

05

Step 5. Install With Daily Updates

Your project manager is on the roof with the crew and sends progress photos. Hidden damage, like rusted purlins or wet insulation, is priced at the unit price in your proposal and approved by you before we fix it.

06

Step 6. Inspection, Warranty and Closeout

The manufacturer inspects the finished roof before it issues the warranty. You get the warranty, the final inspection, lien waivers, and a photo record of the roof, start to finish.

★★★★★Google Review

"Great people, great work and great experience. Great communication by William Fields. Work was done on schedule and exactly as stated. I will use these guys again!"

Mark Davidson, Google review, January 2026

Recent Projects

Two Metal Roofs, Retrofit With PVC

Both buildings had metal roofs at the end of their life. Instead of tearing off the metal, we retrofit both with Duro-Last PVC over new insulation, with new edge metal and gutters. In Foley we tore off a gravel roof and put Duro-Last PVC on a downtown restaurant: see the Foley Brunch and Supper Club roof. In Mobile, a tear-off exposed a rusted-through steel deck: see the roof and deck replacement.

The Homestead Mobile, Theodore, AL

Project detailWhat we built
BuildingTwo-story metal building, about 11,800 square feet of roof
ScopePVC retrofit over the existing metal roof, no tear-off
SystemDuro-Last Duro-Tuff 50 mil white PVC over EPS flute fill and 1.5-inch polyiso board, retrofit over the existing metal
AttachmentRhinobond induction-welded plates: 12 per board in the field, 16 at the perimeter, 18 in the corners. No screws through the membrane
Edges and water290 feet of new wood nailer at the eaves, 300 feet of 6-inch gutters tied into the roof, 170 feet of two-piece compression edge metal
Warranty20-year Duro-Last No-Dollar-Limit warranty plus our 5-year workmanship warranty
CompletedAugust 2026
Wise Builders crew and lift on a commercial roof job at The Homestead in Mobile, AL
Telehandler staging material to the roof
Wise Builders crew induction-welding PVC roof membrane to Rhinobond plates at The Homestead in Mobile, AL
Induction-welding the PVC to its plates, no screws through the membrane
New commercial roof edge and gutter at The Homestead in Mobile, AL by Wise Builders
New eave, edge metal and 6-inch gutter

Mobile SPCA, Mobile, AL

Project detailWhat we built
BuildingAnimal shelter with a standing seam metal roof, about 7,400 square feet
ConditionRusted standing seam panels, 14 skylights, and deteriorated steel purlins in the worst areas
StructureSteel purlin repair: reinforcement plates fabricated and welded overhead from a lift
SystemDuro-Tuff 50 mil white PVC, mechanically attached with reinforced perimeter detailing, over flute fill sized to the standing seam profile and 1.5-inch polyiso board
Details14 skylight curbs rebuilt, 442 feet of new edge and rake metal, 360 feet of eave nailer, new gutters and downspouts
Warranty20-year Duro-Last No-Dollar-Limit warranty
Completed2026
Rusted standing seam metal roof with skylights at Mobile SPCA in Mobile, AL before replacement
Rusted standing seam roof and skylights
Polyiso insulation board fastened over the existing metal roof at Mobile SPCA in Mobile, AL by Wise Builders
Polyiso board fastened over the flute fill
Finished white PVC commercial roof at Mobile SPCA in Mobile, AL by Wise Builders
New 50 mil white PVC roof

On a metal building, the steel under the roof matters as much as the roof. We inspect from underneath and price structural repair as its own line item, so the number you sign is the number you pay.

Why Wise Builders

Why Building Owners and Property Managers Hire Us

01

One Contractor, Roof and Building

We are a licensed general contractor, not only a roofer. When a leak has ruined ceilings, drywall, or insulation, the same crew and the same project manager fix the inside too.

02

One Fixed Price, in Writing

The proposal lists the system, every layer, the warranty term, and unit prices for hidden damage. The price changes only through a written change order you sign first.

03

Built for Small and Mid-Size Buildings

Offices, retail centers, churches, metal shops, and apartments are our focus. Your roof gets a dedicated project manager, not the crew left over from a warehouse job.

The Credentials Behind Every Commercial Roof

Wise Builders holds Alabama General Contractor License #60291 and is a Duro-Last approved contractor, which lets us offer manufacturer No-Dollar-Limit warranties up to 30 years, depending on the system. Every commercial roof also carries our 5-year workmanship warranty. We carry general liability and workers' compensation and are BBB accredited.

Before you sign with anyone, ask for the license number, a certificate of insurance, and a sample of the warranty you will actually receive. A No-Dollar-Limit warranty covers labor and materials for leaks. A materials-only warranty does not. We send ours with the proposal.

★★★★★Google Review

"The contract was clear and all work was performed on schedule. A certificate of compliance was issued by a third party after inspection. It is refreshing to find a company like this."

Ronald Houle, Google review, March 2024

FAQ

Frequently Asked Questions About Commercial Roofing

How much does a commercial roof cost per square foot in Mobile?

On the Gulf Coast, a commercial roof typically runs $3.50 to $22 per square foot. A silicone coating runs $3.50 to $6.00, a single-ply recover $8.00 to $11.00, a PVC or TPO retrofit over metal $6.00 to $8.00, a full TPO or PVC tear-off $13.00 to $16.00, and a standing seam steel roof $15 to $22. For a 10,000 square foot roof, that is roughly $35,000 to $220,000.

What is the best commercial roof for the Gulf Coast?

For most low-slope buildings here, a white PVC or TPO membrane over new insulation is the best value. It reflects heat, handles ponding better than coatings, and carries long manufacturer warranties. PVC is the better pick for restaurants and for retrofits over metal; standing seam metal is the long-life choice on steeper roofs.

TPO, PVC, or metal: which should I choose?

TPO is the lower-cost single-ply. PVC costs a little more and resists grease, chemicals, and fire better, with factory-made flashings. Metal lasts longest but costs the most up front. See our TPO, PVC, and metal roofing pages for side-by-side detail.

How long does a commercial roof last?

A well-installed PVC or TPO roof typically lasts 20 to 30 years, a silicone coating 10 to 20 years before a recoat, and a standing seam metal roof 40 years or more. Twice-a-year maintenance is what gets a roof to the long end of those ranges.

Do you offer No-Dollar-Limit warranties?

Yes. As a Duro-Last approved contractor we offer manufacturer No-Dollar-Limit warranties up to 30 years, depending on the system, plus our own 5-year workmanship warranty. A No-Dollar-Limit warranty covers labor and materials for leaks, not just the membrane.

Can you re-roof while our building is open?

Yes. Most of our commercial roofs are on occupied buildings. We work in sections, dry in each section every day, protect HVAC intakes, and schedule noisy work around your hours.

Let's Talk First

Ready for a Roof That Stops Leaking?

Your commercial roof starts with a free inspection, core cuts, and a written, fixed price. There is nothing to pay and nothing to sign to find out what your roof needs.

Wise Builders Roofing and Renovations holds Alabama General Contractor License #60291, is a Duro-Last approved contractor, and brings one project manager, one written scope, and one fixed price to every commercial roof in Mobile and Baldwin County.

Call our Mobile headquarters at (251) 305-7282 or our Foley office at (251) 270-5270, or send the form and we will set a free roof inspection.

Wise Builders Roofing and Renovations, 6215 Rangeline Rd #105, Theodore, AL 36582 and 105 W Camphor Ave #100A, Foley, AL 36535.

★★★★★Google Review

"William is great to work with. Wise Builders are extremely thorough and professional. Everything was done exactly how and when they said it would be. A++++"

Nate, Google review, May 2026

Schedule a free analysis today